Completed Forward Fuselage Lower Structure (Section 28)

Applied a bead of tank sealant to the bottom flanges of the muffler shroud sides and riveted them to the forward skins. Riveted the muffler shroud ramp to the sides and added a fillet of sealant to the bottom of each seam.

 

 

 

Positioned the firewall assembly on the forward skins and muffler shroud. Added sealant between the skins and firewall and around the curved area where the muffler shroud connects to the firewall and clecoed everything together. Riveted the cover bases to the skin. Riveted the curved part of the firewall to the muffler shroud sides and ramp.

 

 

 

Riveted the firewall angle to the firewall and skins. Dimpled the cowl places and shims and riveted them in place.

 

 

 

Riveted the tunnel sides to the skins and muffler shroud.

 

 

Riveted the routing bracket and fuel selector bracket in place.

img_3453

 

Riveted and bolted to forward center section bulkhead to the tunnel side. Riveted the skins to the cover ribs.

 

 

Sealed and screwed the firewall penetration fittings to the firewall.

img_3458

 

Fabricated and assembled the cabin heat vent assemblies. Then riveted them in place on the firewall along with their control cable brackets.

 

Machine countersunk the battery box attach holes and riveted it to the firewall.

 

Dimpled the cover panel and riveted it to the forward flanges of the cover ribs along with a gazillion nut plates.

 

Forward Fuselage Lower Structure… Done! On to the side structures!

 

 

Today’s Time (hours): 8.0
Fuselage Time (hours): 73.0
Total Time (hours): 527.5

 

Started assembling the lower skins and muffler shroud.

Dimpled the bottom skins and riveted the com antenna doublers and skin stiffeners to them. I’m only installing a single com radio so I only drilled out the right side skin for the antenna. The left side I installed some rivets to fill the starter holes. I did install the left side antenna doubler in case i want to add another radio later. I can just drill out the rivets and upsize the holes to install another antenna.

 

Dimpled the muffler shroud parts. Riveted the doublers and muffler hanger brackets to the shroud sides. Riveted the nut plates to the fuel pump brackets and then riveted the brackets to the shroud ramp.

 

Today’s Time (hours): 2.0
Fuselage Time (hours): 65.0
Total Time (hours): 519.5

 

Continued assembling the firewall

Riveted the angles and lower gusset to the right firewall side. Used tank sealant to Seal the top of the firewall to the sides and clecoed in place along with the top firewall angle and riveted them together. Clecoed the tunnel sides to the firewall assembly. Sealed the firewall center to the sides and top and clecoed in place. Clecoed the upper top angle and gussets in place. Final drilled the nose gear brackets.

 

Today’s Time (hours): 2.0
Fuselage Time (hours): 61.5
Total Time (hours): 516.0

 

Riveted the angles to the left firewall side

Received the new firewall angles from Van’s. Deburred, scuffed, and primed them. Then taped the holes I shouldn’t countersink and countersunk the rest.

img_3420

 

Clecoed the angles and gussets to the firewall. Then back-riveted the left firewall side.

 

Today’s Time (hours): 2.0
Fuselage Time (hours): 59.5
Total Time (hours): 514.0

 

Deburred, Scuffed, and Primed Forward fuse.

Did the deburring and scuffing last night. Neglected to take any pictures. Shot the primer this evening. My firewall parts order showed up so included those as well.

img_3417

 

Today’s Time (hours): 2.0
Fuselage Time (hours): 57.5
Total Time (hours): 512.0